Collection List
FNIRSI DPS-150P 150W Programmable DC Power Supply
Product Resources
You may also like
The FNIRSI DPS-150P is a compact programmable DC power supply for electronics development, troubleshooting and controlled electrical testing. It provides adjustable 0–30 V, 0–5 A output up to 150 W, with constant-voltage and constant-current operation, six stored output presets, live measurement and configurable protection.
DC and supported USB-C PD/QC input options make the DPS-150P particularly useful where a compact, portable DC source is preferable to a conventional mains-powered bench supply.
Precise, repeatable DC control
Voltage can be set in 10 mV increments and current in 1 mA increments. The 2.8-inch display provides live output voltage, current and power information together with operating state, internal temperature and accumulated Ah/Wh data.
Six stored setting groups make commonly used output conditions easy to recall.
PC-controlled testing
Compatible FNIRSI PC software extends the DPS-150P beyond basic power delivery with:
- remote voltage and current control;
- voltage and current logging;
- sequential output;
- voltage sweeps;
- current sweeps; and
- preset management.
These functions support repeatable device testing where voltage or current needs to change in a controlled sequence.
A practical current source for winding-resistance work
The DPS-150P can provide the regulated DC excitation required for practical winding-resistance and low-resistance measurement arrangements.
The DPS-150P establishes a known test current while a suitable external millivolt-resolution instrument measures voltage directly across the test object. Resistance is then calculated using:
R = V / I
| Test condition | Measured voltage |
|---|---|
| 1 A through 1 mΩ | 1 mV |
| 1 A through 0.1 mΩ | 0.1 mV |
| 5 A through 1 mΩ | 5 mV |
| 5 A through 0.1 mΩ | 0.5 mV |
| 5 A through 10 µΩ | 50 µV |
With suitable separate current and voltage-sensing connections, this provides a flexible approach to transformer winding resistance, motor stator winding comparison, conductor and joint investigation, and other controlled-current low-resistance measurements within the DPS-150P's 5 A capability.
The DPS-150P acts as the controlled-current source in this arrangement. It does not itself directly measure resistance or replace the external voltage measurement, Kelvin-style connection, temperature consideration, safe discharge and method controls integrated into a dedicated winding-resistance tester.
Transformer winding-resistance applications
For transformer winding-resistance work, a stable DC excitation current can be selected within the DPS-150P's 5 A capability. Practical inStore application experience may use approximately 1–15% of winding rated current where appropriate to the transformer and measurement objective.
The measured winding terminals and winding temperature should be recorded, sufficient time allowed for inductive effects to settle, and stored magnetic energy safely discharged before test connections are removed.
AS/NZS 60076.1 establishes direct-current winding-resistance measurement requirements for transformers. The approximate 1–15% excitation range above is specialist application guidance and is not presented as a requirement of that Standard.
Motor stator winding applications
For motor-stator winding measurement and comparison, a practical excitation current of approximately 1–10% of nominal winding current may be used where appropriate, subject to the DPS-150P's 5 A maximum output.
Corresponding windings should be measured with consistent current, connection method and temperature basis. The current should be sufficient to produce a stable measurable voltage without causing material winding heating.
Input-source flexibility
The DPS-150P accepts DC input and compatible USB-C PD/QC sources.
DPS-150P is a step-down power supply. Input voltage must therefore be higher than the required output voltage, and the connected source voltage and current determine how much of the Product's 30 V / 5 A / 150 W output envelope can actually be used.
A small USB-C source does not automatically make the complete 150 W output envelope available.
Protection
The DPS-150P provides configurable protection including:
- overvoltage protection;
- overcurrent protection;
- undervoltage protection;
- overpower protection;
- overtemperature protection;
- reverse-input protection; and
- reverse-output protection.
These functions support the power supply and test arrangement but do not remove the need for appropriate electrical test practice.
Specifications
| Specification | Value |
|---|---|
| Product type | Programmable step-down DC power supply |
| Output voltage | 0–30 V |
| Output current | 0–5 A |
| Output power | Up to 150 W |
| Operating modes | Constant Voltage / Constant Current |
| Voltage setting resolution | 10 mV |
| Current setting resolution | 1 mA |
| Input voltage | DC 5–32 V |
| Recommended input range | DC 5–30 V |
| Input protocols | PD / QC supported |
| Preset groups | 6 |
| Load regulation | Manufacturer stated 0.49% |
| Full-load efficiency | Manufacturer stated 96% |
| Display | 2.8-inch, 320 × 240 |
| Output connection | 4 mm banana terminals |
| PC functions | Remote control, logging, sequencing, voltage sweep and current sweep |
| Protection | OVP, OCP, UVP, OPP, OTP, reverse input and reverse output |
| Dimensions | 106 × 76 × 28 mm |
| Weight | Approximately 178 g |
Important low-resistance measurement note
The DPS-150P acts as the controlled-current source in a resistance-measurement setup. It is not itself a micro-ohmmeter or a complete winding-resistance tester.
Useful low-resistance results depend upon the complete measurement arrangement, including the external voltage-measurement instrument, current stability, separate voltage-sensing connections, thermal EMFs, test-object temperature, inductive settling and safe management of stored energy.